HM259048/HM259010 Single row bearings inch

B1:2 mm; Tolerance shaft:h8; D:10 mm; B:4 mm; Coefficient of friction µ min.:0.05; Permissible sliding velocity v max.:5 m/s; d:6 mm; D1:14 mm; Permissible sliding velocity v min.:0.25 m/s; Specific dynamic load factor K:10 N/mm²;

Mass pillow block:441 kg; ba:103.188 mm; Ca:147.803 mm; Max. speed for Taconite seal:425 r/min; Cap bolt recommended tightening torque:4284.4 N·m; Adapter sleeve assembly:SNW 140x7.1/8; Pa:82.7 kN; P90°:400 kN; P150°:222 kN; Bearing:22340 CCK/W33;

B:29.00 mm; Grease Speed Rating Open/Shielded n1:4600 rpm; Accessories:Without Accessories; Fillet Radius ra:2.00 mm; Oil Speed Rating Open/Shielded n2:5600 rpm; Basic Dynamic Radial Load Rating C:79200 N; d:55.000 mm; D:120.0000 mm; Basic Static Radial Load Rating Co:65500 N;

Basic Dynamic Radial Load Rating C:67100 N; Fillet Radius ra:1.50 mm; Basic Static Radial Load Rating Co:65500 N; Oil Speed Rating n2:6700 rpm; Accessories:Shield & Seal; B:39.70 mm; Grease Speed Rating n1:5000 rpm; Sealed Speed Rating n3:5000 rpm; d:40.000 mm; D:90.0000 mm;

B1:225 mm; d1:320 mm; Hydraulic nut:HMV 72 E; G2:G 1/4; G1:33 mm; G:Tr 360x5; B2:234 mm; Mass withdrawal sleeve:28.5 kg; d:340 mm; Nut for removal:HM 3172;

Phase shift output signal:90 °; Limiting speed:5000 r/min; Phase shift output signal tolerance ±:30 °; Mass sensor unit:0.07 kg; Number of pulses per revolution N:32; Duty cycle:50 %; Duty cycle tolerance ±:10 %; Period accuracy ±:4 %; Cable connector type:Free cable end

D:130.0000 mm; Basic Dynamic Radial Load Rating C:88000 N; Basic Static Radial Load Rating Co:71000 N; Accessories:One Shield & Snap-Ri; B:31.00 mm; Fillet Radius ra:2.00 mm; Grease Speed Rating Open/Shielded n1:4400 rpm; Oil Speed Rating Open/Shielded n2:5400 rpm; d:50.000 mm;

r1,2 min.:4 mm; Basic static load rating C0:610 kN; Cb min.:14.5 mm; Basic dynamic load rating C:487 kN; Reference speed:2600 r/min; Ca min.:7 mm; Db min.:177 mm; r3,4 min.:3 mm; Calculation factor Y0:0.9; C:53 mm;

B:80 mm; Da max.:229 mm; r1,2 min.:2.1 mm; B1:95 mm; Calculation factor Y2:3.4; Basic dynamic load rating C:783 kN; Basic static load rating C0:1200 kN; Reference speed:1700 r/min; ra max.:2 mm; b:8.3 mm;

da max.:92 mm; Calculation factor Y0:0.9; d:75 mm; Mass bearing:5.19 kg; D:160 mm; Cb min.:13 mm; Calculation factor Y:1.7; Db min.:149 mm; Da max.:149 mm; Basic dynamic load rating C:416 kN;

Ca min.:5.5 mm; Basic dynamic load rating C:12900 kN; Fatigue load limit Pu:1460 kN; d2 ≈:697 mm; d:600 mm; s1 max.:24.6 mm; Basic static load rating C0:23200 kN; D1 ≈:869 mm; ra max.:6 mm; Da min.:823 mm;

L:869.95 mm; P120°:249 kN; Mass pillow block:298 kg; P180°:267 kN; H2:101.6 mm; PG:1/4 NPT; P60°:669 kN; Initial grease fill:3515.4 g; R1:163.512 mm; Eye bolt:2 x 1/2-13 UNC;

Db:90 mm; Housing:FYTBK 507; Da:88.9 mm; Recommended diameter for attachment bolts, inch G:0.5 in; Thread grub screw G2:M6; Limiting speed:5300 r/min; J:130 mm; Mass bearing unit:0.63 kg; A:35 mm; T:45.3 mm;

Oil Speed Rating Open/Shielded n2:43000 rpm; Fillet Radius ra:0.30 mm; Basic Static Radial Load Rating Co:1360 N; d:7.000 mm; B:7.00 mm; Sealed Speed Rating n3:23000 rpm; Basic Dynamic Radial Load Rating C:3250 N; D:22.0000 mm; Grease Speed Rating Open/Shielded n1:36000 rpm; Accessories:One Seal;

G:M 150x2; Recommended grub screw tightening torque:35 N·m; h:6 mm; Associated spanner:TMFN 23-30; Grub (set) screw size:M10; B3:9 mm; Axial static load carrying capacity:495 kN; B:30 mm; Mass lock nut:2.27 kg; d1:162 mm;